Oil Sump for Audi A3 8L1 VW Golf IV Polo 9N 1.6 Petrol 1.9 Tdi Sdi
Oil Sump for Audi A3 8L1 - VW Golf IV Polo 9N 1.6 Petrol 1.9 Tdi Sdi. The description of this item has been automatically translated. If you notice fluid leaks after an impact on the base of the vehicle, it could possibly be due to the breakage of the vehicle oil Cup motor. There oil Cup it has the shape of a pan and is connected to the lower part of the motor.
Generally it is made of very resistant material, such as steel and, if necessary, it can be removed. Drain the oil circulating in the various parts of the engine. When you change to a new one, the plug of the pot will first be removed, then proceed to the drainage phase. The oil pan is in the same position for all vehicles and therefore easy to identify. In case of breakage, therefore, the car must be turned off and parked on a flat surface.
Then, once the damaged piece has been found, it can be replaced. Engine oil sump replacement: tools required. If you notice the presence of oil patches under your vehicle, the fault should be repaired as quickly as possible in order not to risk even more serious damage to the engine. If you want to save, it is possible replace the piece yourself, without having to resort to the help of a professional.
To get started though, you need to make sure you have. Work keys of various types. New gasket and oil pan. After that you can move on to the next step. How to replace the engine oil pan: preliminary steps.
As a first step, you have to place the car on the appropriate positioning ramps. To be more sure that the vehicle does not slide downwards, it is necessary engage the handbrake and put two metal wedges behind the wheels. If you don't have ramps, you can always use a jack. At this point, you need to check the ramp cup gasket and tighten the screws evenly. Then make sure that the drain plug is well screwed and the sealing washer both in good condition.
Finally you will have to check that the cap thread if everything should be in the right place, without significant wear, the replacement of the oil pan. The first step to take when replacing the oil pan is its own emptying. To operate in total safety and comfort, place the car on a suitable bridge. Then you have to follow the following points to the letter. Remove the exhaust manifold support bracket and a series of bolts and screws. Replace the gasket present between the sump and the crankcase. Then tighten the nuts proceeding gradually. Remove the cup, replace it and reassemble the bolts one by one. We do not process orders until we are sure of 101% compatibility.
To find out the compatibility before purchasing, attach the booklet of your car. How to read the data reported in the booklet. (A) registration number (license plate). (B) date of first registration of the vehicle.
2.1 surname or company name. 2.3 address in the Member State of registration on the date of issue of the document. 3.1 surname or company name. 3.2 name (s) or initial (s) (if applicable). 3.3 address in the Member State of registration on the date of issue of the document.
(E) vehicle identification number (chassis). 1 technically permissible maximum laden mass, with the exception of motorcycles. 2 Maximum permissible laden mass of the vehicle in service in the Member State of registration. 3 Maximum permissible laden mass of the assembly in service in the Member State of registration. (G) mass of the vehicle in service with bodywork and equipped with the coupling device for towing vehicles of categories other than M1. (I) date of registration to which the registration certificate refers. 1 destination and use of the vehicle.
(K) type approval number (if available). 1 distribution among the axles of the technically permissible maximum laden mass (for vehicles with a total mass exceeding 3500 kg) axle 1 (kg). 2 axle 2 (kg), if applicable. 3 axle 3 (kg), if applicable. 4 axle 4 (kg), if applicable. 5 axle 5 (kg), if applicable. 1 technically permissible maximum towed mass with braked trailer (kg). 2 technically permissible maximum towed mass with unbraked trailer (kg). 2 maximum net power (kW) (if available). 3 type of fuel or power source. (Q) power / mass ratio in kW / kg (only for motorcycles). 1 number of seats, including that of the driver. 2 number of standing places (if applicable). 1 sound level with stationary vehicle [dB (A)]. 2 sound level at engine speed rpm × min. 1 CO (g / km og / kWh). 2 HC (g / km og / kWh). 3 NOx (g / km og / kWh). 5 particulate matter for diesel engines (g / km or g / kWh). 7 CO2 (g / km).9 indication of the EC type-approval environmental class. If this is not possible, you can request a free-of-charge deposit and collect it personally at the nearest branch. Delays due to the courier are not attributable to our company but to the courier. Più di 100,000 Km. This item is in the category "Vehicle Parts & Accessories\Car Parts & Accessories\Engines & Engine Parts\Engine Mounts".
The seller is "himagautomotiveindustry" and is located in this country: IT. This item can be shipped worldwide.- Units of measure: Unit
- die quantity: 1
- Manufacturer Part Number: BMO-VW-005
- Country of manufacture: Italy
- Brand: Himag
- mileage: More than 100,000 Km
- Part Number Original OE/OEM: 038103601NA
- Manufacturer Warranty: European
